product datasheet leila series last update 21/6/2012 ordering number family type led color diameter height style optic material holder material fastening status cp11633_lxp3-m leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file (simulated) 0 (simulated) 0 % - available suitable for star pcb ordering number family type led color diameter height style optic material holder material fastening status cp12817_lxp3-rs2 leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 10 degrees 93 % 15.600 available ordering number family type led color diameter height style optic material holder material fastening status cp11632_lxp3-d leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 11 degrees (simulated) 0 % 8.950 available suitable for star pcb ordering number family type led color diameter height style optic material holder material fastening status cp11634_lxp3-o-90 leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 12+34 degrees (simulated) 0 % 3.860 available october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 21/6/2012 note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 21/6/2012 general information - product series especially designed & optimized for xt-e series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 30.04.2010 checked by sn date 25.11.2010 drawn by mav date 25.11.2010 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev drawing title datasheet lxp3 ledil oy tehdaskatu 13 fin-24100 salo finland materials: holder: pc white lens: pmma 2 solder pocket glue groove 14.6 21.6 isometric view scale: 1:1
product datasheet leila series last update 21/6/2012 ordering number family type led color diameter height style optic material holder material fastening status cp11633_lxp3-m leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file (simulated) 0 (simulated) 0 % - available suitable for star pcb ordering number family type led color diameter height style optic material holder material fastening status cp12817_lxp3-rs2 leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 10 degrees 93 % 15.600 available ordering number family type led color diameter height style optic material holder material fastening status cp11632_lxp3-d leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 11 degrees (simulated) 0 % 8.950 available suitable for star pcb ordering number family type led color diameter height style optic material holder material fastening status cp11634_lxp3-o-90 leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 12+34 degrees (simulated) 0 % 3.860 available october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 21/6/2012 note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 21/6/2012 general information - product series especially designed & optimized for xt-e series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 30.04.2010 checked by sn date 25.11.2010 drawn by mav date 25.11.2010 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev drawing title datasheet lxp3 ledil oy tehdaskatu 13 fin-24100 salo finland materials: holder: pc white lens: pmma 2 solder pocket glue groove 14.6 21.6 isometric view scale: 1:1
product datasheet leila series last update 21/6/2012 ordering number family type led color diameter height style optic material holder material fastening status cp11633_lxp3-m leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file (simulated) 0 (simulated) 0 % - available suitable for star pcb ordering number family type led color diameter height style optic material holder material fastening status cp12817_lxp3-rs2 leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 10 degrees 93 % 15.600 available ordering number family type led color diameter height style optic material holder material fastening status cp11632_lxp3-d leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 11 degrees (simulated) 0 % 8.950 available suitable for star pcb ordering number family type led color diameter height style optic material holder material fastening status cp11634_lxp3-o-90 leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 12+34 degrees (simulated) 0 % 3.860 available october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 21/6/2012 note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 21/6/2012 general information - product series especially designed & optimized for xt-e series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 30.04.2010 checked by sn date 25.11.2010 drawn by mav date 25.11.2010 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev drawing title datasheet lxp3 ledil oy tehdaskatu 13 fin-24100 salo finland materials: holder: pc white lens: pmma 2 solder pocket glue groove 14.6 21.6 isometric view scale: 1:1
product datasheet leila series last update 21/6/2012 ordering number family type led color diameter height style optic material holder material fastening status cp11633_lxp3-m leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file (simulated) 0 (simulated) 0 % - available suitable for star pcb ordering number family type led color diameter height style optic material holder material fastening status cp12817_lxp3-rs2 leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 10 degrees 93 % 15.600 available ordering number family type led color diameter height style optic material holder material fastening status cp11632_lxp3-d leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 11 degrees (simulated) 0 % 8.950 available suitable for star pcb ordering number family type led color diameter height style optic material holder material fastening status cp11634_lxp3-o-90 leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 12+34 degrees (simulated) 0 % 3.860 available october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 21/6/2012 note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 21/6/2012 general information - product series especially designed & optimized for xt-e series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 30.04.2010 checked by sn date 25.11.2010 drawn by mav date 25.11.2010 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev drawing title datasheet lxp3 ledil oy tehdaskatu 13 fin-24100 salo finland materials: holder: pc white lens: pmma 2 solder pocket glue groove 14.6 21.6 isometric view scale: 1:1
product datasheet leila series last update 21/6/2012 ordering number family type led color diameter height style optic material holder material fastening status cp11633_lxp3-m leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file (simulated) 0 (simulated) 0 % - available suitable for star pcb ordering number family type led color diameter height style optic material holder material fastening status cp12817_lxp3-rs2 leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 10 degrees 93 % 15.600 available ordering number family type led color diameter height style optic material holder material fastening status cp11632_lxp3-d leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 11 degrees (simulated) 0 % 8.950 available suitable for star pcb ordering number family type led color diameter height style optic material holder material fastening status cp11634_lxp3-o-90 leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 12+34 degrees (simulated) 0 % 3.860 available october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 21/6/2012 note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 21/6/2012 general information - product series especially designed & optimized for xt-e series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 30.04.2010 checked by sn date 25.11.2010 drawn by mav date 25.11.2010 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev drawing title datasheet lxp3 ledil oy tehdaskatu 13 fin-24100 salo finland materials: holder: pc white lens: pmma 2 solder pocket glue groove 14.6 21.6 isometric view scale: 1:1
product datasheet leila series last update 21/6/2012 ordering number family type led color diameter height style optic material holder material fastening status cp11633_lxp3-m leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file (simulated) 0 (simulated) 0 % - available suitable for star pcb ordering number family type led color diameter height style optic material holder material fastening status cp12817_lxp3-rs2 leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 10 degrees 93 % 15.600 available ordering number family type led color diameter height style optic material holder material fastening status cp11632_lxp3-d leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 11 degrees (simulated) 0 % 8.950 available suitable for star pcb ordering number family type led color diameter height style optic material holder material fastening status cp11634_lxp3-o-90 leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 12+34 degrees (simulated) 0 % 3.860 available october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 21/6/2012 note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 21/6/2012 general information - product series especially designed & optimized for xt-e series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 30.04.2010 checked by sn date 25.11.2010 drawn by mav date 25.11.2010 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev drawing title datasheet lxp3 ledil oy tehdaskatu 13 fin-24100 salo finland materials: holder: pc white lens: pmma 2 solder pocket glue groove 14.6 21.6 isometric view scale: 1:1
product datasheet leila series last update 21/6/2012 ordering number family type led color diameter height style optic material holder material fastening status cp11633_lxp3-m leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file (simulated) 0 (simulated) 0 % - available suitable for star pcb ordering number family type led color diameter height style optic material holder material fastening status cp12817_lxp3-rs2 leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 10 degrees 93 % 15.600 available ordering number family type led color diameter height style optic material holder material fastening status cp11632_lxp3-d leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 11 degrees (simulated) 0 % 8.950 available suitable for star pcb ordering number family type led color diameter height style optic material holder material fastening status cp11634_lxp3-o-90 leila assembly xt-e white 21.6 mm 14.6 mm round pmma pc glue ready fwhm efficiency cd/lm gerber file 12+34 degrees (simulated) 0 % 3.860 available october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 21/6/2012 note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 21/6/2012 general information - product series especially designed & optimized for xt-e series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 19th 2012 0:33 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 2 3 2 4 1 4 1 designed by hh date 30.04.2010 checked by sn date 25.11.2010 drawn by mav date 25.11.2010 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev drawing title datasheet lxp3 ledil oy tehdaskatu 13 fin-24100 salo finland materials: holder: pc white lens: pmma 2 solder pocket glue groove 14.6 21.6 isometric view scale: 1:1
|
